Solar Powered Pump Kit - Basic. This solar powered pump kit with submersible pump enables you to move rainwater round the garden without using mains electricity. Turn it on and off by hand. 12 volt 12 watt solar panel and Comet pump.

This is a “project” kit providing components only. You need do-it-yourself skills to fit it.

These do-it-yourself kits can supply a drip feed watering system directly or through a header tank (so that water is available for gravity feed at any time, even through a time switch). You can move water from a low level collecting tank in the garden (or even at ends of a polytunnel or greenhouse) to a storage tank at a higher level. The applications are numerous in allotments, equestrian properties, market gardens and for water features.

1. Solar panel with built-in charger provides 12volt trickle current to a battery (provided by you) during daylight.
2. The battery drives a 12volt pump at any time, up to the capacity of the battery. The pump remains submerged in the water butt or collector tank
3. Manual mode (“basic” kit): without float switches the user can turn on the pump from time to time to pump available water. User must check levels.

In the simple illustration, the solar pump is used to lift the rainwater from a holding tank near the house or building - which could even be underground and out of sight - to a much larger storage tank or cistern further up the garden. The powerful pump will lift water to a head of 30 feet. 

Components for solar pump kit 02

1)  12 watt Solar Charger N31CX Converts daylight into electricity to charge 12V batteries, extending battery life

• Requires only daylight (not direct sunlight)
• Amorphous solar panel charges even in overcast weather
• Blocking diode prevents reverse charging and protects battery discharge at night
• Protects against natural battery discharge and electronic drain
• Easy to connect with crocodile clips, pre-cut holes for easy mounting
• No regulator needed for batteries >40 amp-hours, trickle charge only.
• Rated Power 12 Watts, Max Output Voltage 17.55 Volts
• Optimum Output current 580 milliAmps, cable length 3m
• External dimensions 98(L) x 34(W) x 1.5(D) cm, panel dimensions 90(L) x 29(W) cm

2)        12 volt DC Self-priming submersible LVM pump by ITT. This 12V DC self-priming pump is ready to work off a 12volt battery or solar panel when power goes out. Fully submersible and can be left in the water permanently.

Technical Specifications:

• 12V DC LVM 111 (previously Jabsco) pump made by ITT
• Self-priming and fully submersible pump left in the water permanently.
• Flow rate: 30 litres/min
• Head: max 1 bar  (manufacturer's nominal) at pump and 8 metre head
• Power consumption: 65-80 watts
• Dimensions: 165 (L) x 38 (diameter) mm.
• Weight 0.56 kg

Please note: The battery is not provided in the kit. We recommend the client uses a car battery, between 20 and 100 AH (amp hours), which need not be brand new. Note that the solar charger will not charge a battery from flat; ensure the battery can be charged by a mains charger if it ever gets flat. However, several hours daily use of the pump will not, according to our tests, exhaust a typical car battery… the pump draws 30 watts while the solar panel is delivering 12 watts.

DIY (do-it-yourself) skills needed to install such a kit. The solar panel need mounting on a south facing roof or wall. Tank needs drilling and opening out with a file to the size of the float switch. The electric components need wiring (typically with automotive blade and crimp connectors). Hose pipe needs connecting to the pump with wire or jubilee clip.

If you would like a solar pump like this but you do not want to have to put it together yourself then please look at the Plug'n'Spray solar pump on this web site.

System tested by RainWaterHarvesting.co.uk in real conditions. If you have a question or two please email our "solar" man marcus@rainwaterharvesting.co.uk 

You can download the complete installation manual for solar pumps here.